Easiest Raspberry Pi GPIO LED Project Ever

This will be the easiest Raspberry Pi GPIO LED project ever. If you follow this guide it should take less than 20 minutes to setup and have running. The goal of this project is to get a single LED light blinking based on a Python program running on a Raspberry Pi. In order to do this you will need to use the GPIO pins (the gold colored ones near the SD card and S-video) on the Raspberry Pi. This article will go over materials needed, how to setup the hardware and example software code. This project is meant to be simple for Noobs like us. Easiest Raspberry Pi GPIO LED Project Ever

Materials Needed

Raspberry Pi and all of the basics – Everything needed to get the Raspberry Pi up and running can be found in the Raspberry Pi is an Amazing Small Learning Computer and Starting the Raspberry Pi for the First Time is Easy Articles previously published on this website. These articles will show you were to buy all of the Raspberry Pi basics and how to get it up and running with Raspbian.

Additional Electronics Needed – Below is a list of items you will need for this project. If you do not have these items lying around the house there are also product links on kits we bought and liked.

Jumper wires or leads – These are cheap small wires to connect the GPIO pins to the breadboard. If you are just starting out we suggest getting male to female leads for easy connection to the Pi.  This is what we bought for $9. Foxnovo 3pcs 20cm Multicolored 40-pin Male to Female /Male to Male /Female to Female Breadboard Jumper Wires Ribbon Cables

Additional Resistors – These are cheap and you can never have enough if you plan to do some projects. E-Projects – 400 Piece, 16 Value Resistor Kit (10 Ohm – 1M Ohm)

A Starter Kit – This is the most important additional item you will need. If you do not already have a Raspberry Pi we have included a full starter kit below.

Hardware Configuration

Make sure the Raspberry Pi is unplugged!

Quick breadboard explanation – breadboards are pretty simple tools. They simply allow for connecting wires together without having to solder anything. In a breadboard there are horizontal relays of 5 slots each and vertical relays of 25 slots. Each row of 5 and 25 is connected together but not to each other. The picture to the right gives a visual on how things are electrically connected.

Jumper Wires – Take two female to male jumper wires (I suggest using red and black if you have them for positive and negative) and connect the red one to GPIO pin 7 and the black one to GPIO pin 6 (see the diagram below for a visual on how the pins are numbered). After this connect the red wire to a horizontal relay section on the breadboard. For this example we will connect to slot j9 on the breadboard. Connect the black wire to any of the vertical negative (blue) relay channels.

LED Light – Pick any color you like. You will notice that the LED has one connection that is longer than the other. The longer one is the positive and the short end is the negative. Plug the positive (longer) end into the same channel on the breadboard as your positive (red) wire. In this example we will use slot f9. Plug the negative (shorter) in any horizontal channel that is not in the same as the positive connection. In this eample we will use f7.Easiest Raspberry Pi GPIO LED Project Ever schemstic

Resistor – Use between a 220 Ohm and a 270 Ohm for this. If you bought the resistor kit above everything will be labeled. If you did not use this online calculator . Plug one end of the resistor into the same horizontal channel that the negative end of the LED is plugged into. For this example we are using slot g7. Plug the other end into the negative vertical relay channel (blue) so it is connected with the negative (black) jumper wire.

Final Hardware Configuration – When everything is said and done the breadboard should look something like this. I know it is hard to see.

 

For more detail: Easiest Raspberry Pi GPIO LED Project Ever


About The Author

Ibrar Ayyub

I am an experienced technical writer holding a Master's degree in computer science from BZU Multan, Pakistan University. With a background spanning various industries, particularly in home automation and engineering, I have honed my skills in crafting clear and concise content. Proficient in leveraging infographics and diagrams, I strive to simplify complex concepts for readers. My strength lies in thorough research and presenting information in a structured and logical format.

Follow Us:
LinkedinTwitter

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top