converter

KEMET ADVANCES HYBRID ALUMINUM POLYMER CAPACITOR TECHNOLOGY

KEMET ADVANCES HYBRID ALUMINUM POLYMER CAPACITOR TECHNOLOGY

KEMET, a subsidiary of Yageo Corporation (“Yageo”) (TAIEX: 2327) and leading global supplier of electronic components, announces the launch of three hybrid aluminum polymer capacitor series: A780, PHA225, and PHH225. These AEC-Q200 qualified capacitors offer a combination of highly conductive polymer technology and liquid electrolytic material in a hybrid design, resulting in an outstanding electrical […]

KEMET ADVANCES HYBRID ALUMINUM POLYMER CAPACITOR TECHNOLOGY Read More »

NEW ULTRABK DC DC CONVERTERS FEATURE TWO STAGE DESIGN

NEW ULTRABK DC/DC CONVERTERS FEATURE TWO-STAGE DESIGN

Fully Integrated DC/DC Converters from Murata Feature Patented Ultra-Compact, High-Efficiency Design Leveraging a multi-patented design that significantly reduces the footprint and height of power-conversion circuitry, Murata has introduced the UltraBK™ family of compact, low-profile, fully-integrated DC/DC converters. The UltraBK™ converters are aimed at space-constrained applications such as IT and network infrastructure equipment. In addition to unprecedented space

NEW ULTRABK DC/DC CONVERTERS FEATURE TWO-STAGE DESIGN Read More »

TI RELEASE TPS62912 TPS62913 FAMILY OF LOW NOISE DC DC SWITCHING REGULATORS

TI RELEASE TPS62912, TPS62913 FAMILY OF LOW-NOISE DC/DC SWITCHING REGULATORS

Texas Instruments released the TPS62912 and TPS62913 family of low-noise DC/DC switching regulators with integrated ferrite-bead compensation. They offer low noise of 20 µVRMS for frequencies ranging from 100 Hz to 100 kHz and ultra-low output-voltage ripple of 10 µVRMS. Traditional low-noise power supply architectures include such technology like DC/DC converters, low-noise LDO, and an off-chip filter, like a ferrite bead. Integrating ferrite-bead

TI RELEASE TPS62912, TPS62913 FAMILY OF LOW-NOISE DC/DC SWITCHING REGULATORS Read More »

TEXAS INSTRUMENTS TPS61099 SYNCHRONOUS BOOST CONVERTER

TEXAS INSTRUMENTS’ TPS61099 SYNCHRONOUS BOOST CONVERTER

Texas Instruments’ converter features 800 nA ultra-low quiescent current Texas Instruments’ TPS61099x is a synchronous boost converter with 1 µA ultra-low quiescent current. The device is designed for products powered by alkaline batteries, NiMH rechargeable batteries, Li-Mn batteries, or rechargeable Li-Ion batteries where a high efficiency under light-load condition is critical to achieving long battery life operation.

TEXAS INSTRUMENTS’ TPS61099 SYNCHRONOUS BOOST CONVERTER Read More »

THE NEW BLYST840 PACKS A SURPRISING AMOUNT OF IOT HARDWARE INTO ITS TINY FINGERTIP SIZE

THE NEW BLYST840 PACKS A SURPRISING AMOUNT OF IOT HARDWARE INTO ITS TINY, FINGERTIP SIZE

BLYST Nano is a tiny ARM Cortex Module with Bluetooth and 30 I/O, but next product BLYST840 is a finger-tip size, 32-bit ARM Cortex-M4F module with Bluetooth 5 and 46 I/O; a powerful upgrade of a system on a module indeed. Built around the Nordic nRF52832 Bluetooth SOC and the powerful 64MHz ARM cortex- M4Fprocessor, the new

THE NEW BLYST840 PACKS A SURPRISING AMOUNT OF IOT HARDWARE INTO ITS TINY, FINGERTIP SIZE Read More »

ISOLATED FULL DUPLEX RS 485 TRANSCEIVERS

ISOLATED FULL-DUPLEX RS-485 TRANSCEIVERS

This module is an isolated full-duplex differential line driver and receiver for TIA/EIA RS485/RS422 applications. The module is ideal for long transmission lines because the ground loop is broken to allow for a much larger common-mode voltage range. The symmetrical barrier of the device is tested to provide isolation of 2500Vrms between bus line Trans-receiver and the logic-level interface.

ISOLATED FULL-DUPLEX RS-485 TRANSCEIVERS Read More »

BMR481 48 V TO LOAD DIRECT CONVERSION DC DC CONVERTERS

BMR481 48 V-TO-LOAD DIRECT CONVERSION DC/DC CONVERTERS

Flex Power Modules’ converters are first generation direct conversion products Flex Power Modules’ BMR481 DC/DC converter addresses the growing need for higher energy efficiency levels in datacenters and cloud computing infrastructures. This converter offers an input range of 40 V to 60 V targeting 48 V to 54 V nominal supplies and a programmable 0.5 V to 1.35 V output. The 12 mm

BMR481 48 V-TO-LOAD DIRECT CONVERSION DC/DC CONVERTERS Read More »

Scroll to Top