converter

TECHAR1

How to Generate a High-Precision Waveform Using a DAC and a Custom PCB

In this article, we’ll develop firmware that will serve as the basis for high-precision, high-speed signal generation. I recently designed an arbitrary waveform generator (AWG) PCB that is built around a C8051F360microcontroller and a TxDAC from Analog Devices. These two ICs communicate via a parallel interface that allows me to generate higher-frequency analog signals by seeking […]

How to Generate a High-Precision Waveform Using a DAC and a Custom PCB Read More »

moRFeus – A field configurable wideband frequency converter and signal generator

moRFeus – A field-configurable wideband frequency converter and signal generator

MoRFeus is a 30 MHz–6 GHz field-configurable Fractional-N wideband frequency converter and signal generator. Its LCD display and button interface enable dynamic field-level configuration – from switching between signal generator and other modes, to setting the local oscillator frequency and more. It was designed for wideband frequency up- and down-conversion – with an LO frequency

moRFeus – A field-configurable wideband frequency converter and signal generator Read More »

USB To 12V Boost Converter

USB To 12V Boost Converter

This project provides 12V output from any USB power source, like PC USB port, USB adapter or power banks. LM2577ADJ boost converter IC is the heart of the project. The IC can handle load up to 800mA, it’s advisable to use only 200mA load on output to be on the safe side. The LM2577 are

USB To 12V Boost Converter Read More »

Flex Power Modules launches 1000W DC DC advanced bus converter

Flex Power Modules launches 1000W DC/DC advanced bus converter

Based upon Flex Power Modules’ Hybrid Regulated Ratio (HRR) topology, the BMR480 DC/DC bus converter module delivers up to 1000W and 96.2A peak power. The BMR480 DC/DC advanced bus converter targets high-end and high-power applications. It is available in an industry-standard and low-profile quarter-brick-format with dimensions of 58.4 x 36.8 x 12.19mm (2.30 x 1.45

Flex Power Modules launches 1000W DC/DC advanced bus converter Read More »

Temperature Sensor Sample

Temperature Sensor Sample

Temperature/Force Sensor Sample This sample uses SPI communication. A temperature/force sensor is connected to a ADC, then ADC is connected to raspberry Pi2 through SPI Pins. Raspberry Pi2 reads the sensor analog input data and output it to the screen. This is basically a simplified version of Potentiometer sensor sample, which has a LED light

Temperature Sensor Sample Read More »

Raspberry Pi – homemade level converter for serial communication rs232 3.3 volts to 5 volts TTL for AVR microcontroller

Raspberry Pi – homemade level converter for serial communication rs232 3.3 volts to 5 volts TTL for AVR microcontroller

I found that the Raspberry Pi serial interface rs232, described in a older post by myself, was too bulky. Pi and AVR should be connected through a less amount of wires. So I’ve searched the best hints to solder a cheap and uncomplicated level converter, that can directly be connected between the GPIO of the

Raspberry Pi – homemade level converter for serial communication rs232 3.3 volts to 5 volts TTL for AVR microcontroller Read More »

Buck converter starts up in just 70 ms

Buck converter starts up in just 70 ms

Features Order Custom Programmed Parts PMBus/I2C Compliant Serial Interface – Telemetry Read Back includes VIN, IIN, VOUT, IOUT, Temperature, Duty Cycle and Faults – Programmable Voltage, Current Limit, Digital Soft-Start/Stop, Sequencing, Margining, OV/UV and Frequency Synchronization (250kHz to 1MHz) ±0.5% Output Voltage Accuracy Over Temperature Integrated 16-Bit ADC VOUT Range: 0.5V to 5.5V (VOUT0, VOUT1)

Buck converter starts up in just 70 ms Read More »

Scroll to Top